Skip to main content
Reference | Publication | Energy Systems Division

ES 2011 Publications

2011

E. V. Timofeeva, Yu, W., France, D. M., Singh, D., and Routbort, J. L., “Base fluid and temperature effects on the heat transfer characteristics of SiC in ethylene glycol/H2O and H2O nanofluids”, Journal of Applied Physics, vol. 109, p. 5, 2011.

N. Shidore, Rask, E., Vijayagopal, R., and Jehlik, F., “PHEV Energy Management Strategies at Cold Temperatures with Battery Temperature Rise and Engine efficiency Improvement Considerations”, in 2011 SAE World Congress & Exposition, Detroit, MI, USA, 2011, p. 1.

“Equipped to Charge: Wiring, Chargers, and Meters: Attributes and Costs”. p. 15, 2011.

J. L. Routbort, “Nanofluids for HEV Cooling Applications”. p. 18, 2011.

M. M. Mintzand Jarvis, D., “Employment Impacts of Early Markets for Hydrogen and Fuel Cell Technologies”. p. 20, 2011.

S. Som, “Discussion on IC Engine Spray Applications: Recent Progress in CFD Modeling and Challenges”. p. 13, 2011.

M. M. Mintzand Han, J., “Energy and Greenhouse Gas Emissions of Renewable Natural Gas as a Vehicle Fuel”, 2011.

S. Somand Longman, D. E., “Nozzle Flow Characterization of Alternate Fuels for Compression Ignition Engine Applications”. p. 26, 2011.

S. Som, Longman, D. E., Luo, Z., Plomer, M., and Lu, T., “Three Dimensional Simulations of Diesel Sprays Using n-Dodecane as a Surrogate”, presented at the 20111009, 2011, p. 14.

J. L. Routbort, France, D. M., Yu, W., Singh, D., and Timofeeva, E. V., “Engineering Nanofluids for Efficient Heat Transfer”. p. 29, 2011.

U. Balachandran, “High Dielectric Constant Capacitors for Power Electronic Systems”. p. 14, 2011.

N. Demas, Erck, R. A., Ajayi, O. O., and Fenske, G. R., “Tribological studies of coated pistons sliding against cylinder liners under laboratory test conditions”, p. 18, 2011.

N. Kimand Rousseau, A., “Comparison between Rule-Based and Instantaneous Optimization for a Single-Mode, Power-Split HEV”, in 2011 SAE World Congress & Exhibition, Detroit, MI, USA, 2011, p. 1.

D. J. Santini, Vyas, A. D., Saucedo, D., and Jungers, B., “Where Are the Market Niches for Electric Drive Passenger Cars?”, presented at the 20110101, 2011, p. 1.

J. P. Katsoudas, Timofeeva, E. V., and Segre, C. U., “EAXL: Electrodeposition Assisted X-ray Lithography”, p. 10, 2011.

N. Shidore, Ickes, A., Wallner, T., Rousseau, A., and Ehsani, M., “Evaluation of Ethanol Blends for PHEVs using Engine-in-the-Loop”, p. 8, 2011.

T. Levinson, “Idling Reduction Tools You Can Use”. p. 13, 2011.

S. Som, “Validation of Reduced Chemical Kinetic Mechanisms for Engine Simulations”. p. 44, 2011.

Z. Luo, Plomer, M., Lu, T., Som, S., and Longman, D. E., “A reduced mechanism for biodiesel surrogates with low temperature chemistry for compression ignition engine applications”, Combustion Theory and Modeling, vol. 16, no. 2, p. 1, 2011.

J. Wang, Botterud, A., Bessa, R. J., Keko, H., Carvalho, L., Issicaba, D., Sumaili, J., and Miranda, V., “Wind Power Forecasting Uncertainty and Unit Commitment”, Applied Energy, vol. 86, no. 11, p. 9, 2011.

J. L. Routbort, France, D. M., Yu, W., Singh, D., and Timofeeva, E. V., “Engineering Nanofluids for Efficient Heat Transfer”. p. 29, 2011.

U. Balachandran, “High Dielectric Constant Capacitors for Power Electronic Systems”. p. 14, 2011.

N. Demas, Erck, R. A., Ajayi, O. O., and Fenske, G. R., “Tribological studies of coated pistons sliding against cylinder liners under laboratory test conditions”, p. 18, 2011.

M. M. Mintzand Han, J., “Energy and Greenhouse Gas Emissions of Renewable Natural Gas as a Vehicle Fuel”, 2011.

D. J. Santini, Vyas, A. D., Saucedo, D., and Jungers, B., “Where Are the Market Niches for Electric Drive Passenger Cars?”, presented at the 20110101, 2011, p. 1.

J. P. Katsoudas, Timofeeva, E. V., and Segre, C. U., “EAXL: Electrodeposition Assisted X-ray Lithography”, p. 10, 2011.

N. Shidore, Ickes, A., Wallner, T., Rousseau, A., and Ehsani, M., “Evaluation of Ethanol Blends for PHEVs using Engine-in-the-Loop”, p. 8, 2011.

T. Levinson, “Idling Reduction Tools You Can Use”. p. 13, 2011.

S. Som, “Validation of Reduced Chemical Kinetic Mechanisms for Engine Simulations”. p. 44, 2011.

N. Kimand Rousseau, A., “Comparison between Rule-Based and Instantaneous Optimization for a Single-Mode, Power-Split HEV”, in 2011 SAE World Congress & Exhibition, Detroit, MI, USA, 2011, p. 1.

W. Yu, France, D. M., and Routbort, J. L., “Forced Convective Boiling of Ethylene Glycol/Water Mixtures Inside a Small Tube”, Journal of ASTM International, vol. 8, no. 2, p. 18, 2011.

S. Somand Longman, D. E., “Integrated Nozzle Flow, Spray and Combustion Modeling Using KH-ACT Primary Breakup Model & Detailed Chemistry”. p. 29, 2011.

T. Wallnerand Duoba, M., “Alternative fuels and propulsion systems: A U.S. perspective”, p. 15, 2011.

S. Snyder, “WIndiana Indiana Renewable Energy Conference”. p. 21, 2011.

U. Balachandran, Lee, T. H., Park, C. Y., Dorris, S. E., and Akinjiola, O. P., “Hydrogen Transport Membrane Technology for Ethylene Production”, presented at the 20111001, 2011, p. 2.

Z. Luo, Plomer, M., Lu, T., Som, S., and Longman, D. E., “A reduced mechanism for biodiesel surrogates with low temperature chemistry for compression ignition engine applications”, Combustion Theory and Modeling, vol. 16, no. 2, p. 1, 2011.

J. Wang, Botterud, A., Bessa, R. J., Keko, H., Carvalho, L., Issicaba, D., Sumaili, J., and Miranda, V., “Wind Power Forecasting Uncertainty and Unit Commitment”, Applied Energy, vol. 86, no. 11, p. 9, 2011.

G. R. Fenske, Erck, R. A., and Eryilmaz, O., “Coatings for Centrifugal Compression: Poster”. p. 2, 2011.

J. P. Katsoudas, Timofeeva, E. V., and Segre, C. U., “Metal Patterning by Electrodeposition Assisted X-ray Lithography”, p. 30, 2011.

C. Bojanowski, Gepner, B., Kwasniewski, L., Rawl, C., and Wekezer, J., “Roof Crush Resistance and Rollover Strength of a Paratransit Bus”, in 8th European LS.DYNA Conference, Strasburg, France, 2011, p. 13.

G. R. Fenske, Erck, R. A., and Eryilmaz, O., “Coatings for Centrifugal Compression: Presentation”. p. 23, 2011.

M. M. Mintz, “Gaseous Fuels: What's Here and What's Coming”. p. 14, 2011.

T. Bohn, “Metering Issues and Technology-DOE Grid Interaction Tech Team”. p. 16, 2011.

R. Sivaramakrishnan, Liu, W., Davis, M. J., Som, S., and Longman, D. E., “A High Temperature Model for the Combustion of Methylbutanoate”, presented at the 20111009, 2011, p. 8.

R. Scarcelli, Wallner, T., Matthias, N., Salazar, V. M., and Kaiser, S. A., “Mixture Formation in Direct Injection Hydrogen Engines: CFD and Optical Analysis of Single- and Multi-Hole Nozzles”. p. 18, 2011.

T. Levinson, “Idling Reduction Makes $ense”. p. 16, 2011.

K. Holmberg, Andersson, P., and Erdemir, A., “Global energy consumption due to friction in passenger cars”, p. 37, 2011.

R. Vijayagopaland Rousseau, A., “System Analysis of Multiple Expert Tools”, in 2011 SAE World Congress & Exhibition, Detroit, MI, USA, 2011, p. 11.

S. Somand Longman, D. E., “Spray-Combustion Modeling set-up at Argonne National Laboratory”. p. 7, 2011.

J. Kwon, Wang, X., Ahluwalia, R. K., and Rousseau, A., “Impact of Fuel Cell System Design Used in Series Fuel Cell HEV on Net Present Value (NPV)”, p. 7, 2011.

S. Somand Longman, D. E., “Modeling & Simulation Capabilities at Argonne for ICE Applications”. p. 45, 2011.

J. L. Sullivan, Clark, C. E., Yuan, L., Han, J., and Wang, M. Q., “Life-Cycle Analysis Results for Geothermal Systems in Comparison to Other Power Systems: Part II”, Argonne National Laboratory, Argonne, IL USA, 2011.

F. You, Tao, L., Graziano, D. J., and Snyder, S. W., “Optimal design of sustainable cellulosic biofuel supply chains: Multiobjective optimization coupled with life cycle assessment and input-output analysis”, AIChE Journal, vol. 58, no. 4, p. 3, 2011.

S. Arora, Vyas, A. D., and Johnson, L., “Projections of highway vehicle population, energy demand, and CO2 emissions in India to 2040”, Natural Resources Forum, vol. 35, no. 1, p. 13, 2011.

“Transportation and Electricity Convergence Session 2: National Lab Perspective (Sub-metering Hardware and Protocols)”. p. 24, 2011.

A. Rousseau, “Impact of Future Vehicle System Improvements on Battery Size, Usage and Cost”. p. 27, 2011.

T. Wallner, “Correlation Between Speciated Hydrocarbon Emissions and Flame Ionization Detector Response for Gasoline/Alcohol Blends”, Journal of Engineering for Gas Turbines and Power, vol. 133, no. 8, p. 8, 2011.

J. L. Routbort, France, D. M., Singh, D., and Timofeeva, E. V., “Engineering Nanofluids for Efficient Heat Transfer”. p. 29, 2011.

L. L. Gaines, Sullivan, J. L., Burnham, A. J., and Belharouak, I., “Life-Cycle Analysis for Lithium-Ion Battery Production and Recycling”, presented at the 20110115, 2011, p. 17.

L. L. Gaines, “Going Around Again: Getting the Most from your Lithium-Ion Battery Materials”. p. 23, 2011.

E. V. Timofeeva, Moravek, M. R., and Singh, D., “Improving the Heat Transfer Efficiency of Synthetic Oil with Silica Nanoparticles”, p. 25, 2011.

T. Wallner, “Alternative Fuels for Transportation: The Quest for the Silver Bullet”. p. 44, 2011.

J. Han, Mintz, M. M., and Wang, M. Q., “Life Cycle Analysis of Renewable Hydrogen from Waste”. p. 17, 2011.

B. Ma, Narayanan, M., Liu, S., and Balachandran, U., “Growth of PLZT Films on Metal Foils for Power Electronics Applications”. p. 31, 2011.

S. Som, Longman, D. E., Luo, Z., Plomer, M., Lu, T., Senecal, P. K., and Pomraning, E., “Simulating Flame Lift-Off Characteristics of Diesel and Biodiesel Fuels Using Detailed Chemical-Kinetic Mechanisms and LES Turbulence Model”, in ASME 2011 Internal Combustion Engine Division Fall technical Conference, Morgantown, WV USA, 2011, p. 12.

J. L. Routbort, Singh, D., Timofeeva, E. V., Yu, W., and France, D. M., “Pumping power of nanofluids in a flowing system”, Journal of Nanoparticle Research, vol. 13, no. 3, p. 9, 2011.

S. Som, “Compilation of Spray A Modeling Efforts”. p. 31, 2011.

R. Scarcelli, Wallner, T., Matthias, N., Salazar, V., and Kaiser, S., “Numerical and Optical Evolution of Gaseous Jets in Direct Injection Hydrogen Engines”, in 2011 SAE World Congress & Exhibition, Detroit, MI, USA, 2011, p. 1.

A. Elgowainy, Mintz, M. M., and Brown, D., “Hydrogen Delivery Infrastructure Analysis”. p. 27, 2011.

C. E. Clark, Han, J., Burnham, A. J., Dunn, J. B., and Wang, M. Q., “Life-Cycle Analysis of Shale Gas and Natural Gas”, Argonne National Laboratory, Argonne, IL USA, 2011.

S. Arora, Wu, M., and Wang, M. Q., “Update of Distillers Grains Displacement Ratios for Corn Ethanol Life-Cycle Analysis”, Argonne National Laboratory, Argonne, IL USA, 2011.

S. Som, Longman, D. E., Luo, Z., Plomer, M., and Lu, T., “Modeling Biodiesel Spray Flame Lift-Off and Emission Characteristics Using a Detailed Mechanism for Methyl Decanoate as Surrogate”. p. 27, 2011.

C. Lorenzo-Martin, Ajayi, O. O., Smith, C., and Krol, S., “Environmentally Friendly Surface Hardening of 4140 Steel for Tribological Applications”, in ASME/STLE 2011 International Joint Tribology Conference, 2011, p. 3.

T. Wallner, Matthias, N., and Scarcelli, R., “Influence of Injection Strategy in a High-Efficiency Hydrogen Direct Injection Engine”, SAE International Journal of Fuels and Lubricants, vol. 5, no. 1, p. 12, 2011.

R. N. Gurram, Datta, S., Lin, Y. J., Snyder, S., and Menkhaus, T. J., “Removal of enzymatic and fermentation inhibitory compounds from biomass slurries for enhanced biorefinery process efficiencies”, Bioresource Technology, vol. 102, no. 17, p. 10, 2011.

S. Som, “Inner Nozzle Flow and Spray Modeling for Compression Ignition Engine Applications”, presented at the 20111201, 2011, p. 97.

J. L. Sullivan, Gaines, L. L., and Burnham, A. J., “Role of Recycling in the Life Cycle of Batteries”, presented at the 20110302, 2011, p. 8.

M. M. Mintzand Han, J., “Benefits and Barriers to Renewable Natural Gas as a Vehicle Fuel”. p. 14, 2011.

A. Kastengren, Powell, C. F., Dufresne, E. M., and Walko, D. A., “Application of X-ray Fluorescence to Turbulent Mixing”, Journal of Synchrotron Radiation, vol. 18, p. 5, 2011.

G. R. Fenske, “Lubricants: Pathway to Improving Fuel Efficiency of Legacy Fleet Vehicles”. p. 1, 2011.

T. Wallner, “Correlation Between Speciated Hydrocarbon Emissions and Flame Ionization Detector Response for Gasoline/Alcohol Blends”, Journal of Engineering for Gas Turbines and Power, vol. 133, no. 8, p. 8, 2011.

J. L. Routbort, France, D. M., Singh, D., and Timofeeva, E. V., “Engineering Nanofluids for Efficient Heat Transfer”. p. 29, 2011.

L. L. Gaines, Sullivan, J. L., Burnham, A. J., and Belharouak, I., “Life-Cycle Analysis for Lithium-Ion Battery Production and Recycling”, presented at the 20110115, 2011, p. 17.

L. L. Gaines, “Going Around Again: Getting the Most from your Lithium-Ion Battery Materials”. p. 23, 2011.

S. Somand Longman, D. E., “Numerical Study Comparing the Combustion and Emission Characteristics of Biodiesel to Petrodiesel”, Energy Fuels, vol. 25, no. 4, p. 14, 2011.

E. V. Timofeeva, Moravek, M. R., and Singh, D., “Improving the Heat Transfer Efficiency of Synthetic Oil with Silica Nanoparticles”, p. 25, 2011.

R. F. Kulakand Bojanowski, C., “Modeling of Cone Penetration Test Using SPH and MM-ALE Approaches”, presented at the 20110523, 2011, p. 10.

L. L. Gainesand Burnham, A. J., “How to Choose the Best Alternative for Your Fleet-FAST!”. p. 13, 2011.

W. Yu, France, D. M., Timofeeva, E. V., Singh, D., and Routbort, J. L., “Convective Heat Transfer of Nanofluids in Turbulent Flow”. p. 40, 2011.

C. Lorenzo-Martin, Ajayi, O. O., and Fenske, G. R., “Enhancement of Tribological Performance of 6061 Aluminun Alloy by Second Phase Hardening Via Friction Stir Processing”, in ASME/STLE 2011 International Joint Tribology Conference , Los Angeles, CA, USA, 2011, p. 4.

R. A. Erck, Ajayi, O. O., Lorenzo-Martin, C., and Fenske, G. R., “Frictional Anisotropy in Boundary Regime: Effect of Surface Texture”. p. 42, 2011.

S. Som, “Compilation of Spray A Modeling Efforts”. p. 31, 2011.

T. Wallner, “Alternative Fuels for Transportation: The Quest for the Silver Bullet”. p. 44, 2011.

J. Han, Mintz, M. M., and Wang, M. Q., “Life Cycle Analysis of Renewable Hydrogen from Waste”. p. 17, 2011.

B. Ma, Narayanan, M., Liu, S., and Balachandran, U., “Growth of PLZT Films on Metal Foils for Power Electronics Applications”. p. 31, 2011.

S. Som, Longman, D. E., Luo, Z., Plomer, M., Lu, T., Senecal, P. K., and Pomraning, E., “Simulating Flame Lift-Off Characteristics of Diesel and Biodiesel Fuels Using Detailed Chemical-Kinetic Mechanisms and LES Turbulence Model”, in ASME 2011 Internal Combustion Engine Division Fall technical Conference, Morgantown, WV USA, 2011, p. 12.

J. L. Routbort, Singh, D., Timofeeva, E. V., Yu, W., and France, D. M., “Pumping power of nanofluids in a flowing system”, Journal of Nanoparticle Research, vol. 13, no. 3, p. 9, 2011.